IDIOMA  
MIEMBROS
¿Olvidó su clave?
¿AúN NO ESTá REGISTRADO?
¿QUé PUEDO HACER?
- Agregar un modelo a mi Showroom (necesita Identificarse o Registrarse)

- Ver mis Showrooms Favoritos

- Buscar Showrooms de otros miembros

- Conocer otros miembros de la Comunidad

- Navegar nuestros Foros

HOY EN MODELERSITE.COM
Ver más >>
MODELER SITE - LA REVISTA

 
CORREO
Si quiere recibir noticias acerca de las actualizaciones, por favor agregue su email a la lista.
ENVIE SU E-MAIL
  TéCNICAS
>> Algunos trucos
>> Aplicando calcas
>> Blindados: Técnica de la sal
>> Como construir modelo de auto con las puertas abiertas
>> Cómo se construye un modelo
>> Confección de una lona para vehículos militares
>> Construyendo cascos en "scratch"
>> Construyendo a kit Vacu en 1/48
>> Desgastes con la técnica de la esponja
>> Detallando amortiguadores en motos escala 1/12
>> El "Weathering"
>> Ensuciado usando pigmentos paso a paso
>> Equivalencias de colores de competición para pinturas Tamiya
>> Las cadenas en los T55
>> Modelado de un busto, Paso a paso
>> Pintando caras con acrílicos
>> Pintando con lacas automotivas
>> Pintando ruedas en 5 pasos
>> Pintando una figura paso a paso
>> Pintar ¿es la clave del modelismo estático?
>> Realizando pintura saltada
>> Realizando terminaciones oxidadas en vehículos militares
>> Ruedas!
>> T-34/76 Round up de kits 1/35, todas las versiones
>> Tabla de conversión de Tamiya a Humbrol y FS
>> Trabajando con Alclad2
>> Trucos para desgastes para modelistas novicios
>> Utilizando la masilla: una guía para novicios

Esta página incluso todo el arte gráfico es propiedad registrada 2006/2010 - Sitemap
 
Blindados  Fórmula uno  Autos  Motos  Aviones  Otros 
 

Scale-Master Showroom Favoritos Identificarse Registrarse
 

1969 Camaro Part 09

Kit / Modelo  

Not available

Fabricante  

Not available

Código de Producto  

Not available

Escala  

1/12

Descripción  

Continued progress. See Part 1 for history and intended direction for this project.

Part 10 click the link

URL Relacionada  

http://www.modelersite.net/viewShowRoom.php?id_contenido=1988

URL Relacionada  

Tipo de sujeto  

Autos

Estado  

En construcción

Envíe un E-mail al miembro  

Solo para miembros

Vistas  

10563

Facebook  


Dejar un comentario
Solo para miembros registrados
The remote oil filter set up was machined from… (big surprise…) aluminum.
The filter is from the kit, slightly reworked with decals I made.
The carbs are installed and plumbed, still need to make the linkages.
The door panels are ready for installation. I machined the bezels for the locks and used straight pins locks. (Driver’s side is unlocked, passenger side is locked.)I decided to hand paint the silver trim instead of BMF for a “less than brand new†look.
Except for the dash, the interior is done.
I added a lap belt for the passenger seat...
and an 8-Ball shifter knob.
The rear brakes are finished; I went with drums since my real one has them. I made them from mostly CA glue on an aluminum core with a shell of styrene and turned them on the lathe. (CA machines nicely...) The studs are small bolts embedded in the core.
The hardware that mounts the backing plates to the axle tubes and makes up the brake line fittings is more machined aluminum nuts and bolts. The cast texture was added by hand brushing Testors metalizer.Weights have also been added to balance the driveshaft… Don’t want any high speed vibrations, especially with those 4:11 gears.
First test fit of the body/interior/chassis to verify my measurements were correct before going on to prepping the body.
First test fit of the body/interior/chassis to verify my measurements were correct before going on to prepping the body.